看下面,G54,G55就是同時加工兩個工件。同一工件,移位就是同一座標再加一句G54 X--Y--就好了
H002 = +000001.4500 (加工深度 );
H019 = +000000.0001 (LNS 搖動形狀 );
H018 = +000000.0303 (LNM 搖動模式 思考);
H011 = +000000.1000 (電極減寸量 );
;
G90 G25 G11;
G54 G00X-060.00 Y 00.0 M98P0001 (加工座標);
/G55 G00X-038.00 Y 00.0 M98P0001 (加工座標);
M02;
N0001 (精加工子程式);
G00 Z16.0 (放電開始高度,大約3毫米);
MTRL000010;
MDIV16 AOD0.030 LEJL0.150 LEJS90.0;
/C007 LNSH019 LNMH018 STEP H011-[0.1500] G01 Z H002+[0.1700] M04;
C006 LNSH019 LNMH018 STEP H011-[0.1000] G01 Z H002+[0.1200] M04;
C005 LNSH019 LNMH018 STEP H011-[0.0650] G01 Z H002+[0.0780] M04;
C004 LNSH019 LNMH018 STEP H011-[0.0500] G01 Z H002+[0.0520] M04;
C003 LNSH019 LNMH018 STEP H011-[0.0340] G01 Z H002+[0.0370] M04 (VDI24);
C002 LNSH019 LNMH018 STEP H011-[0.0200] G01 Z H002+[0.0200] M04 (VDI20);
/C803 LNSH019 LNMH018 STEP H011-[0.0100] G01 Z H002+[0.0100] M04 (VDI18);
G00Z20.0 (安全高度);
M99;
看下面,G54,G55就是同時加工兩個工件。同一工件,移位就是同一座標再加一句G54 X--Y--就好了
H002 = +000001.4500 (加工深度 );
H019 = +000000.0001 (LNS 搖動形狀 );
H018 = +000000.0303 (LNM 搖動模式 思考);
H011 = +000000.1000 (電極減寸量 );
;
G90 G25 G11;
G54 G00X-060.00 Y 00.0 M98P0001 (加工座標);
/G55 G00X-038.00 Y 00.0 M98P0001 (加工座標);
M02;
;
;
N0001 (精加工子程式);
G00 Z16.0 (放電開始高度,大約3毫米);
MTRL000010;
MDIV16 AOD0.030 LEJL0.150 LEJS90.0;
/C007 LNSH019 LNMH018 STEP H011-[0.1500] G01 Z H002+[0.1700] M04;
C006 LNSH019 LNMH018 STEP H011-[0.1000] G01 Z H002+[0.1200] M04;
C005 LNSH019 LNMH018 STEP H011-[0.0650] G01 Z H002+[0.0780] M04;
C004 LNSH019 LNMH018 STEP H011-[0.0500] G01 Z H002+[0.0520] M04;
C003 LNSH019 LNMH018 STEP H011-[0.0340] G01 Z H002+[0.0370] M04 (VDI24);
C002 LNSH019 LNMH018 STEP H011-[0.0200] G01 Z H002+[0.0200] M04 (VDI20);
/C803 LNSH019 LNMH018 STEP H011-[0.0100] G01 Z H002+[0.0100] M04 (VDI18);
G00Z20.0 (安全高度);
M99;
;