夾式送料機操作說明書/耐銳送料機熱1已有 12 次閱讀 2012-08-05 16:32 標籤: 送料機夾式送料機的用途GS-906N簡易操作順序及說明1. 材料線設定: 送料機/夾式送料機固定座置放材料,手動閥On (No.1)夾住材料,材料下緣與模具同高或略高0-0.1mm.2.送料時間設定衝床:355°,送料機:送料至0(按衝床運轉方向,轉動皮帶輪,把副尺移卻至本尺0對齊)。3.調整料厚: 送料機/夾式送料機A.送料機之設定:手動閥Off(No.2),料厚指示環向左旋轉旋緊之0為0.B.人工調整:(1).移動座於上死點(0°),手動閥On(No.1),材料鬆緊之間,向左旋0.05mm並固定之。(2).固定座於上死點(180°)不放鬆,手動閥On(No.1),材料鬆緊之間,向左旋0.05mm並固定之。4.送距調整:A.衝床時間:90°(送料終點。 送料機/夾式送料機B.鬆開M16螺母,以T型扳手調整至所需尺寸,並固定M16螺母。注:送距不穩定時,請留意送距調整螺絲固定環是否鬆動。5.放鬆點設定:A.時機:送料完成後,遵梢定位於材料。 送料機/夾式送料機B.鬆開放鬆凸輪之M8螺絲,調整放鬆線使其對準放鬆點,固定M8螺絲即可。GS-1006 simple sequence of opeations and description 送料機/夾式送料機1. Material line setPlace materials in holder, manual valve On (No.1) grip material, make material bottom align with the mold or slightly higher than 0-0.1mm2 feeding time settingWhen power press is 355 °, Feeding: Feeding to 0 (in the direction of press operation, turn the pulley, the deputy ruler has moved to align the scale 0).3 Adjust material thicknessA. Feeder of the setting: Manual Valve Off (No.2), Counterclockwise rotate indicator ring of mterial thickness to “0”. 夾式送料機的用途B. manual adjustments:(1) Move the seat at the top position (0 °), manual valve On (No.1), turn 0.05mm in counterclockwise and fixed it.(2) bracket at top position (180 °) and do not relax, manual valve On (No.1), turn 0.05mm in counterclockwise and fixed it.4. Feeding pitch adjustment: 送料機/夾式送料機A. Press Time: 90 ° (feed end).B. Loosen the M16 nut with T-wrench to adjust to the setting length, and fix M16 nut. Note: If the feeding pitch is unstable, please pay attention to adjustable screw loose or not.5. Loose settings: 送料機/夾式送料機A. time: when finish feeding, follow pin in the material.B. Loosen the screws M8 cam, adjust the line so it is on relax, fixation M8 screws.型式Feed Model製造號碼Serial No.:材料寬度Material width放鬆角度Pilot release可調整Adjustable材料厚度Material thickness送料機械Feed Mechanism曲軸傳動Crankshaftdrive送料長度Feed length安裝位置Installation location左邊Left of press送料角度Feed angle送料方向Feed direction左-右L--R
夾式送料機操作說明書/耐銳送料機熱1已有 12 次閱讀 2012-08-05 16:32 標籤: 送料機夾式送料機的用途GS-906N簡易操作順序及說明1. 材料線設定: 送料機/夾式送料機固定座置放材料,手動閥On (No.1)夾住材料,材料下緣與模具同高或略高0-0.1mm.2.送料時間設定衝床:355°,送料機:送料至0(按衝床運轉方向,轉動皮帶輪,把副尺移卻至本尺0對齊)。3.調整料厚: 送料機/夾式送料機A.送料機之設定:手動閥Off(No.2),料厚指示環向左旋轉旋緊之0為0.B.人工調整:(1).移動座於上死點(0°),手動閥On(No.1),材料鬆緊之間,向左旋0.05mm並固定之。(2).固定座於上死點(180°)不放鬆,手動閥On(No.1),材料鬆緊之間,向左旋0.05mm並固定之。4.送距調整:A.衝床時間:90°(送料終點。 送料機/夾式送料機B.鬆開M16螺母,以T型扳手調整至所需尺寸,並固定M16螺母。注:送距不穩定時,請留意送距調整螺絲固定環是否鬆動。5.放鬆點設定:A.時機:送料完成後,遵梢定位於材料。 送料機/夾式送料機B.鬆開放鬆凸輪之M8螺絲,調整放鬆線使其對準放鬆點,固定M8螺絲即可。GS-1006 simple sequence of opeations and description 送料機/夾式送料機1. Material line setPlace materials in holder, manual valve On (No.1) grip material, make material bottom align with the mold or slightly higher than 0-0.1mm2 feeding time settingWhen power press is 355 °, Feeding: Feeding to 0 (in the direction of press operation, turn the pulley, the deputy ruler has moved to align the scale 0).3 Adjust material thicknessA. Feeder of the setting: Manual Valve Off (No.2), Counterclockwise rotate indicator ring of mterial thickness to “0”. 夾式送料機的用途B. manual adjustments:(1) Move the seat at the top position (0 °), manual valve On (No.1), turn 0.05mm in counterclockwise and fixed it.(2) bracket at top position (180 °) and do not relax, manual valve On (No.1), turn 0.05mm in counterclockwise and fixed it.4. Feeding pitch adjustment: 送料機/夾式送料機A. Press Time: 90 ° (feed end).B. Loosen the M16 nut with T-wrench to adjust to the setting length, and fix M16 nut. Note: If the feeding pitch is unstable, please pay attention to adjustable screw loose or not.5. Loose settings: 送料機/夾式送料機A. time: when finish feeding, follow pin in the material.B. Loosen the screws M8 cam, adjust the line so it is on relax, fixation M8 screws.型式Feed Model製造號碼Serial No.:材料寬度Material width放鬆角度Pilot release可調整Adjustable材料厚度Material thickness送料機械Feed Mechanism曲軸傳動Crankshaftdrive送料長度Feed length安裝位置Installation location左邊Left of press送料角度Feed angle送料方向Feed direction左-右L--R